Hudson-valley-lighting ENDICOTT 272 Manuel d'utilisateur télécharger pdf

271 & 272

Hudson Valley Lighting, Inc.

P.O. Box 7459

106 Pierces Road

Newburgh, NY 12550

(800) 814-3993

www.hudsonvalleylighting.com

GENERAL

1. To ensure the success of the fixture installation, the following instructions

and

diagram(s) should be read and understood.

2. All electrical connections must be made in accordance with the National

Electric

code and local codes and ordinances. If you are uncertain of the methods of

installing electrical wiring and lighting fixtures secure the services of a qualified

licensed electrician.

3. TOOLS NEEDED: Blade screwdriver, phillips screwdriver, slip joint

pliers or small adjustable wrench, wire cutter/stripper, electrical current tester,

stepladder and electrical tape. NOTE: The important safeguards and

instructions outlined on this sheet are not meant to cover all possible

conditions and situations that may occur. It must be understood that common

sense, caution and care are factors that cannot be built into any product.

Caution and care must be supplied by the person(s) installing, operating and

maintaining this lighting fixture.

INSTALLATION PREPARATION

1. TURN OFF THE ENTIRE ELECTRICAL CIRCUIT TO WHICH THE

LIGHTING FIXTURE IS TO BE ATTACHED. Move the appropriate circuit

breaker to the “off position or completely remove the fuse controlling the

circuit.

2. If an existing fixture is being replaced, remove it and note to which of the

wires in the outlet box the fixture was attached. DO NOT SEPARATE ANY

OTHER WIRES THAT MAY BE IN THE BOX. DO NOT DAMAGE THE

INSULATION OF OLDER WIRING. In regular circumstances the BLACK

wire will be the “Hot” lead and the WHITE wire will be the “Neutral” or

“Common” lead. A GREEN or BARE COPPER wire is the “Ground”. In older

buildings it is always good practice to reconfirm the polarity of the wiring.

3. This fixture is desig

ned to be mounted on a standard round or octagon box. The

box must be securely mounted to the structure of the building.

FIXTURE INSTALLATION

1. Remove the fixture, shades and parts bag(s) from the carton. Before

discarding the carton, double check packing to make certain that all parts are

found.

2. Remove the 3 screws holding the mounting plate to the fixture.

3. Pull the wires in the outlet box through the center hole of the mounting

plate. Attach the mounting plate to the outlet box. (The green ground screw

should face out). Align the mounting plate so the bottom screw hole is exactly

at the bottom.

4. Fasten the green fixture wire to the green or bare copper wire in the box or

fasten it to the mounting plate with green screw provided.

NEVER FASTEN THE GROUND WIRE TO THE BLACK OR “HOT”

WIRE! FAILURE TO FOLLOW THIS INSTRUCTION COULD RESULT IN

SERIOUS INJURY OR DEATH!

5. Fasten the white fixture wire to the white wire in the outlet box. Fasten

the wires to together with an approved fastener (wire nut).

Starting about 1” below the fastener, tightly wrap connection with electrical

tape so that the tape seals the end of the fastener.

Make sure that there is no exposed wire or strands that could cause a

dangerous short circuit !

6. Connect the black fixture wires to the black wire in the outlet box.

Fasten the joined wires as in step 5.

7. Place the fixture over the mounting plate. and fasten it in place with the 3

screws.

8. Place the rings onto the top and bottom of the shade(s)

9. Place the shade(s) onto the socket cover(s).

10. Install the lamp(s) light bulb(s).

NOTE: This fixture is rated for 60 watt type B, BA, C or CA lamp(s).

DO NOT EXCEED RECOMMENDED WATTAGE !

11. Restore power to circuit at breaker or fuse box.

Approved fastener

(Wire nut)

Electrical tape

1 2

Résumé du contenu

Page 1 - Electrical tape

271 & 272 Hudson Valley Lighting, Inc. P.O. Box 7459 106 Pierces Road Newburgh, NY

Page 2

271 & 272 Português Hudson Valley Lighting, Inc. P.O. Box 7459 106 Pierces Road Newburgh, NY 12550

Modèles reliés ENDICOTT 271

Commentaires sur ces manuels

Pas de commentaire

Hudson-valley-lighting ENDICOTT 272 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Hudson-valley-lighting ENDICOTT 272. Hudson Valley Lighting ENDICOTT 272 User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés ENDICOTT 271

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Hudson-valley-lighting ENDICOTT 272